Most Wisconsin homeowners pay somewhere between $10,000 and $38,000 for a metal roof. The final number depends on the metal, the roof size and shape, and the crew. One source lists the Wisconsin average for metal roofing at $10,203, or $8.81 per square foot. Standing seam costs more than that average. This guide shows the ranges, what drives them, and how to get a firm price.
TL;DR
- Wisconsin metal roofing averages about $8.81 per square foot, or $10,203, in one 2026 cost report.
- Corrugated steel is the low end. Standing seam steel and aluminum cost more. Copper costs the most.
- Complex roofs with valleys and dormers run about 15% to 25% higher.
- Winter is the slow season for roofers. Booking then may bring a lower price.
- Get a written, line-by-line quote. Poor installation causes most roof failures, so the crew matters as much as the metal.
Table of Contents
- What a metal roof costs in Wisconsin
- Metal roof cost by material and style
- Metal roof cost by home size
- What raises or lowers the price
- Metal vs. asphalt shingles in Wisconsin
- When to book to pay less
- Perspective
- Get a metal roof price for your house
- How to compare metal roof quotes
- FAQ
- Sources
What a metal roof costs in Wisconsin
Start with the state figure. This Old House reports that Wisconsin metal roofing averages $10,203, or $8.81 per square foot. It puts all new-roof costs in the state between $5,466 and $17,887.
Treat that average as a floor for planning. It blends cheaper panel types with premium ones. A standing seam system on a typical house usually lands higher.
Nationally, metal roofing runs $4 to $30 per square foot, and about 60% of the cost is labor. Asphalt shingles run $1.50 to $6.00 per square foot in the same report.
Two things follow from this:
- Labor is most of the bill. Who installs the roof matters.
- The spread is wide. A single "average" tells you little until you know your material and your roof.
Metal roof cost by material and style
The type of metal sets the price per square foot. These are 2026 U.S. installed ranges from a metal roof cost guide:
| Metal roof type | Installed cost per sq ft |
|---|---|
| Corrugated steel | $7 to $12 |
| Stone-coated steel | $8 to $15 |
| Standing seam steel | $12 to $18 |
| Standing seam aluminum | $14 to $20 |
| Standing seam copper | $28 to $48 |
These are national figures. Wisconsin prices follow the same pattern. Local labor rates, roof design and the season move the final number.
Corrugated and exposed-fastener panels
These are the lowest-cost metal option. Panels are screwed through the face of the metal. The fasteners are visible on the roof. Many homeowners choose this style for sheds, garages and additions.
Stone-coated steel
Steel panels with a stone-chip surface. They look more like shingles or tile. They sit in the middle of the price range.
Standing seam
Standing seam panels run from the ridge to the eave. The seams stand up and the fasteners are hidden. This is the most popular premium metal system for homes. We install it. See our page on standing seam metal roofing in Wisconsin for the system details.
Copper and other premium metals
Copper costs several times more than steel. It suits accents, porches and bay roofs more often than whole roofs.
Metal roof cost by home size
Roof area matters more than the footprint of the house. Pitch and extra planes add area. A 2,000-square-foot house often has a larger roof than 2,000 square feet.
The same cost guide lists these 2026 U.S. totals:
| Roof size | Corrugated | Stone-coated | Standing seam |
|---|---|---|---|
| 1,200 sq ft | $10,000 to $17,000 | $11,000 to $21,000 | $17,000 to $25,000 |
| 1,800 sq ft | $15,000 to $25,000 | $17,000 to $32,000 | $25,000 to $38,000 |
For a 2,000-square-foot roof, a standing seam estimate based on RSMeans data gives a very wide range of $15,080 to $78,860. The top of that range reflects premium metals and complex roofs. Most Wisconsin homes sit well below it.
Quick way to estimate your roof
- Find your roof area. Ask a roofer to measure it, or use a roof-measurement report.
- Pick a material from the table above.
- Multiply area by the per-square-foot range.
- Add 15% to 25% if the roof has many valleys, dormers or chimneys.
This gives a ballpark only. A written quote after an inspection is the real number.
What raises or lowers the price
Roof complexity
Valleys, dormers, hips, skylights and chimneys all need extra cutting and flashing. Complex roofs run about 15% to 25% higher than a plain gable roof in the same cost guide. Valleys take the most skill. Water runs hardest there.
What the quote includes
The cost guide's installed figures cover synthetic underlayment, peel-and-stick protection at eaves and valleys, drip edge, ridge cap and a single-layer tear-off. They leave out replacing structural decking. Ask every contractor the same questions:
- Is tear-off included?
- What underlayment is used?
- Is ice-and-water protection included at eaves and valleys?
- What is the price per sheet if rotted decking is found?
- Are trim, flashing and ridge vents included?
Panel gauge and supply
Thicker steel and better coatings cost more. Panel suppliers price on gauge, length and trim packages. For a look at how panel and trim pricing is built, see custom-length standing seam panels and their trim and flashing packages.
Installation quality
Labor is about 60% of the national cost, so it is also where a bad job costs you most. Most roof failures come from poor workmanship, not from the material. A cheap quote with thin detail often means shortcuts at flashing, valleys and edges.
Ventilation and decking
A roof that cannot breathe ages faster, whatever it is made of. Read our note on how poor attic ventilation can cut roof life short. Fixing ventilation during a re-roof is cheaper than fixing it later.
Metal vs. asphalt shingles in Wisconsin
Asphalt costs less up front. National figures put shingles at $1.50 to $6.00 per square foot against $4 to $30 for metal. Metal can last decades longer, so some owners who plan to stay put choose it for that reason.
Wisconsin adds its own demands. Roofs here face heavy snow, ice, wind and hail. Metal sheds snow well. Good installation matters either way.
For comparison, our published price for roof replacement is $7,500 to $18,000. That is our range for roof replacement. We do not publish a metal roof price, because standing seam, synthetic and cedar roofs are priced per house after an inspection. For a full breakdown of roof prices in our area, read our Wisconsin roof replacement cost guide.
If you are weighing metal against a synthetic look, see metal roofing vs. DaVinci synthetic roofing.
When to book to pay less
Winter is the slow season for roofers. GAF notes that some contractors offer incentives in winter. It also warns that snow, ice, wind, short days and slower material handling can delay work.
Metal panels handle cold better than shingles. One manufacturer-side installer notes that metal is less affected by cold than shingles are. That makes metal a fair candidate for off-season work.
Practical steps:
- Get quotes in late fall.
- Ask for a firm start window, not a date.
- Confirm how the crew protects the open roof during snow.
- Ask about material lead times. Custom panels can take weeks.
We wrote a winter roof replacement checklist that walks through this.
Perspective
We have owned and supervised roofing jobs in Wisconsin for over 25 years. Our view is simple. The metal matters, but the install matters more.
A metal roof is only as good as its flashing, valleys, fasteners and underlayment. We supervise the work ourselves and document each stage. You see what is under the metal before it is covered.
We also give honest repair-or-replace advice. Not every roof needs a full replacement. When it does, we tell you why. Our guide on repair or replace shows how we decide.
If storm damage is the reason, we help you work through the insurance claim. We pair that with products that carry strong warranties.
Heather
Get a metal roof price for your house
We install standing seam metal, DaVinci and CeDUR synthetic, cedar shake, TPO flat roofing and architectural shingles. We serve Dodge, Washington, Fond du Lac and Ozaukee counties and the Southeast Wisconsin area. Storm damage repair and insurance claim help are part of the service.
Request an inspection and a written quote on our roofing services page. You get the scope, the materials and the price in writing.
How to compare metal roof quotes
Use the same checklist on every bid.
- Material and gauge. Name the panel type, metal and coating.
- Scope. Tear-off, underlayment, flashing, vents, trim and cleanup.
- Decking. How rot is handled and priced.
- Warranty. Who backs the material and who backs the labor.
- Documentation. Photos of work as it progresses.
- Insurance. Whether the contractor will meet your adjuster.
A low price that skips items on this list is not a lower price. It moves cost to later.
FAQ
How much is a metal roof on a 2,000-square-foot home?
For a standing seam roof of that size, one cost guide gives a wide range of $15,080 to $78,860. Most homes fall well below the top end. A roof inspection gives a firm figure for your house.
What is the average cost of a new roof in Wisconsin?
One 2026 report puts new roofs in Wisconsin between $5,466 and $17,887. Our published roof replacement range is $7,500 to $18,000.
What is the cheapest month for roofing?
Winter is the slow season, and some contractors offer incentives then. Weather can delay work. Ask for a start window and a plan for protecting the roof.
Will insurance cover my roof?
Coverage depends on your policy and the cause of damage. Storm damage such as hail or wind is often the type of claim homeowners file. We help homeowners work through the claim, and your insurer makes the coverage decision.
Sources
- The Cost of a Roof Replacement in Wisconsin, This Old House
- How Much Does a Standing Seam Metal Roof Cost, This Old House
- Metal Roof Cost 2026, ContractorRanks
- Metal Roof vs. Asphalt Shingles, NerdWallet
- Can You Replace a Roof in the Winter, GAF
- Does a Metal Roof Cost More to Install, AB Martin
- Contractor Supply, standing seam panels